Stucco Molding

Home / Stucco Molding

Stucco Molding Services in Toronto

Stucco molding services in Toronto are an absolute necessity for your home’s exterior. They’re not only stylish, but they protect the structure of your home from the elements. This can be a tough act to pull off, especially if you’re just getting started with stucco molding.

What Is Stucco Molding?

Stucco molding is a material with a smooth, glossy surface. It’s used on walls and ceilings to cover up cracks and imperfections, and it’s also used in decorative ways. Stucco is available in many different textures and colors; you can even paint it if you want.

The basic idea behind stucco is that it’s supposed to look like stone. The stucco mastic used to make these products is made from gypsum, which has the same composition as the minerals that make up limestone and marble. The difference between stucco and stone is how much of the original material remains after it’s been formed into a wall or ceiling. Stone still has some of its original structure left in it; stucco only retains those parts that are needed for structural purposes (such as holding up the building).

Stucco mastic can be made using either sand or cement, but it must be mixed with water before being applied to your walls or ceilings. Once mixed, though, stucco doesn’t require any additional ingredients or additives; as long as there are no air pockets inside your walls when they’re being built, they’ll stay solid all

What Is Stucco Molding?

Stucco molding is a material with a smooth, glossy surface. It’s used on walls and ceilings to cover up cracks and imperfections, and it’s also used in decorative ways. Stucco is available in many different textures and colors; you can even paint it if you want.

The basic idea behind stucco is that it’s supposed to look like stone. The stucco mastic used to make these products is made from gypsum, which has the same composition as the minerals that make up limestone and marble. The difference between stucco and stone is how much of the original material remains after it’s been formed into a wall or ceiling. Stone still has some of its original structure left in it; stucco only retains those parts that are needed for structural purposes (such as holding up the building).

Stucco mastic can be made using either sand or cement, but it must be mixed with water before being applied to your walls or ceilings. Once mixed, though, stucco doesn’t require any additional ingredients or additives; as long as there are no air pockets inside your walls when they’re being built, they’ll stay solid all

How To Make Stucco Molding

Make sure you have a good supply of clean, dry sandpaper. You can use an electric sander, but I find it takes longer and is more difficult to hold the piece in place while sanding.

To make your stucco molding, you will need some plaster of paris (which is made from lime and sand), wood or plastic strips to form the molding, and a flat surface for rolling the plaster.

First make sure that you have a good supply of clean, dry sandpaper. You can use an electric sander, but I find it takes longer and is more difficult to hold the piece in place while sanding.

Now mix up enough plaster of paris for about four pieces (or one 8″ x 8″ square). The ratio is 1 part plaster of paris to 3 parts water. If you want to make larger pieces (or if there are more than 4 pieces), then add another tablespoonful or two extra water per pound of plaster.

Use a wooden spoon to stir the plaster until it’s smooth and thick enough to spread easily on your work table or floor.

Then take one piece at a time (use a cloth under them so they don’t stick), and spread some paste onto

HOW TO FINISH STUCCO MOLDING

The first thing to do is remove the old stucco from the mold. You can use a putty knife or scraper to gently pry out the old stucco. If you have a stiff compound, you may have to scrape it off with a putty knife as well.

Once you have removed all of the old stucco, clean up any remaining stucco dust with a wet rag.

Next, mix up some new stucco molding compound and apply it to both sides of your mold. You can use either water-based or latex-based stucco molding compound; they’re both great choices.

After mixing up your stucco, apply it to the back side of your mold using a roller brush. Make sure that the surface is completely smooth — no air bubbles or bumps! Once you’ve applied it evenly across both surfaces (both front and back), let it dry for at least 24 hours before removing it again by scraping off any excess material with a putty knife or other hard tool.

Why the Moulding Matters

The moulding around a door frame is the part of the frame that stops your door from swinging in. It’s not just decoration, it protects your walls from damage by keeping the weight of your door on the frame. The moulding should be flush with the surrounding wall, and no more than 3/4″ away from any other wall surface.

The main purpose of moulding is to provide a strong base for your door, so that it doesn’t fall down if you move or knock it over. This can be important if you have children or pets in the house. If you don’t want to put up with this problem, then go ahead and put up a decorative moulding around your door frames – but be aware that it won’t protect them properly.

Don't hesitate to contact us any time

Or

What Our Clients Says About Kirgil Construction

or

Stephanie Rioux Toronto

5/5

Very professional and knowledgeable team.

Alisa Rose Toronto
5/5
They did amazing work. Cleaned up after themselves and you can’t beat the price. I absolutely recommend them.
Mark Toronto
5/5

Great experience all around. The team did an amazing job and left the place as clean as they entered.

Make An Appointment
all over the Greater Toronto Area.

Feel free to take service from us because we believe in solution at anytime

Request a Quote